U Bend Tube | U bent Tubes U Bent Stainless Steel Tubes for Heat Exchanger

Our Stainless Steel U bend Tube / U bent Stainless Steel tubes included ASTM A213 ASME SA213 TP304 TP304L TP304H TP316 TP316L TP316Ti TP317 TP317L TP317LMN TP321 TP321H TP347H TP309S TP310S TP310H 904L N08904 254SMo S31254, ASME SA789 S31803 S32205 S32750 S32304 S32760 S32101.

Guanyu Tube is a specialized manufacturer of Stainless Steel U Bend Tube / Stainless Steel U bent Tubes for U Tube Heat Exchanger (U bent Stainless Steel Tube for U bent Tube Heat Exchanger). Our U Bend Tube Tube-bending production line, installed in 2007. Solution annealing after bending will be processed to lower the residual stress, and followed by Hydrostatic testing/Pneumatic test and Dye Penetrant testing if required.

Guanyu Tube Supplied U Bend Tube Technical Details
U bend Heat Exchanger Tubes Standard Specification
U bend Tube Application
U bend Tubes Mainly Testing Item
U bend Tubes Size
Dimensional Tolerances of U Bend Tube
U bend Heat Exchanger Tubes Production Process
U bend Stainless Steel Tube Exported Countries
Guanyu Tube Stainless Steel U bend Tube Date Sheet
U bend Tube Related Link

Guanyu Tube Supplied U Bent Tube Technical Details

a. All tubes are cut to the specified leg lengths and internally cleaned with air, ends are deburred.
b. Before packing, both ends of U-bends are capped with plastic caps.
c. Vertical separators for each radius.
d. Packing lists, covered with plastic, are placed on each plywood case for easy identification of order details, including exact list of radius and lengths inside.
e. Surface condition Finished U Bend Tube shall be free of scale, without scratches after bending

U bent Heat Exchanger Tubes Standard Specification

1. ASTM A688/A688M-2017 Specification for Seamless and Welded Austenitic Stainless Steel Feedwater Heater Tubes
2. ASTM A556/A556M-2017 Standard Specification for Seamless Cold-Drawn Carbon Steel Feedwater Heater Tubes
3. U Bend Tube for Heat Exchanger Specification

Stainless Steel U bent Tube Application

U Bend tube heat exchangers designed for high temperature applications, especially steam condensing or hot oil systems.

Stainless Steel U Bend Tube are widely used in heat exchanger systems. Heat exchanger equipment on the basis of stainless steel U-tube is essential in strategically important and critical fields nuclear and petrochemical machine building. Mainly Application in Boiler, heat exchanger, super heater, feedwater heater, condenser. Thïs model is selected when differential expansion makes a fixed tube sheet exchanger unsuitable and when conditions preclude a floating head type (HPF) selection.

U Bent Tubes Mainly Testing Item

1. Heat Treatment and Solution Annealing / Bright Annealing
2. Cutting to required length and deburring;
3. Chemical Composition Analysis Test With 100% PMI and One tube from each heat by Direct Reading Spectrometer
4. Visual Test and Endoscope Test for Surface Quality Test
5. 100% Hydrostatic Test/Pneumatic test and 100% Eddy Current Test
6. Ultrasonic Test subject to the MPS (Material Purchase Specification)
7. Mechanical Tests includes Tension Test, Flattening Test, Flaring Test, Hardness Test
8. Impact Test subject to Standard request
9. Grain Size Test and Intergranular Corrosion Test
10. Ultrasoic measuring of Wall Thickness
11. Stress Relieve Annealing on U bend Parts after bending

U Bend Tube | U bent Tubes U Bent Stainless Steel Tubes for Heat Exchanger

U Bend Tubes Size

		BWG	BWG	BWG	BWG	BWG	BWG	BWG	BWG
		25	22	20	18	16	14	12	10
		WT mm	WT mm	WT mm	WT mm	WT mm	WT mm	WT mm	WT mm
Outside Diameter	Outside Diameter	0.508	0.71	0.89	1.24	1.65	2.11	2.77	3.40
mm	inch		kg/m	kg/m	kg/m	kg/m	kg/m	kg/m	kg/m
6.35	1/4	0.081	0.109	0.133	0.174	0.212
9.53	3/8	0.126	0.157	0.193	0.257	0.356	0.429
12.7	1/2		0.214	0.263	0.356	0.457	0.612	0.754
15.88	5/8		0.271	0.334	0.455	0.588	0.796	0.995
19.05	3/4		0.327	0.405	0.553	0.729	0.895	1.236
25.4	1		0.44	0.546	0.75	0.981	1.234	1.574	2.05
31.75	1 1/4		0.554	0.688	0.947	1.244	1.574	2.014	2.641
38.1	1 1/2		0.667	0.832	1.144	1.514	1.904	2.454	3.233
44.5	1 3/4				1.342	1.774	2.244	2.894	3.5
50.8	2				1.549	2.034	2.574	3.334	4.03
63.5	2 1/2				1.949	2.554	3.244	4.214	5.13
76.2	3				2.345	3.084	3.914	5.094	6.19
88.9	3 1/2				2.729	3.609	4.584	5.974	7.27
101.6	4					4.134	5.254	6.854	8.35
114.3	4 1/2					4.654	5.924	7.734	9.43

Dimensional Tolerances of U Bend Tube

According to TEMA R.C.B. and ASTM A566, ASTM A688

3.1 Diameter of tube in the U bent portion

At the bent portion of a U-tube for R = 2 × D or greater, neither the major nor minor diameter of the tube shall deviate from the nominal diameter prior to bending by more than 10 %.

If less than 2 × D is speciﬁed, tolerances could be greater, provided that Entropie agrees prior to order.

3.2 Wall thickness in U bent portion

The wall thickness of the tube in the U-bent section shall not be less than value determined by the equation:

Where:

tf wall thickness after bending, in. [mm],
T speciﬁed minimum tube wall thickness, in. [mm],
R centerline bend radius, in. [mm], and
D nominal outside tube diameter, in. [mm].

3.3 Tube leg length

In the case of U-tubes, the length of the tube legs as measured from the point of tangency of the bend and the tube leg to the end of the tube leg, shall not be less than speciﬁed, but may exceed the speciﬁed values by the amount given here below :

Leg length [mm]

Up to and incl. 6000 mm :                    -0 / +3.2 mm
Over 6000 mm to 9000 (incl) :              -0 / +4.0 mm
Over 9000                                            -0 / + 4.8 mm

3.4 Difference in leg length

The difference in length of tube leg of U tube shall not be greater than 1/8 in. (3.2mm) unless otherwise specified

3.5 End of tube : squareness

The end of any tube may depart from square by not more than:

0.25 mm for tubes up to 5/8” [15.9 mm]
0.40 mm for tubes higher than 5/8” [15.9 mm]

3.6 Leg spacing

The leg spacing measured between the points of tangency of the bend to the legs shall not vary from the value (2 R − speciﬁed tube outside diameter) by more than 1⁄16 in.[1.5 mm] where R is the center-line bend radius.

3.7 Bent portion curvature

The bent portion of the U-tube shall be substantially uniform in curvature, and not to exceed 6 1⁄16 in. [1.5 mm] of the nominal center-line radius.

3.8 Deviation from the plane of bend

Permissible deviation from the plane of bend (Fig. 1) shall not exceed 1⁄16 in. [1.5 mm] as

measured from the points of tangency.

The dimensions for heat exchanger tube in special grades may differ from the above,please contact us.

U bend Tubes Production Process

U-Bend-Tubes-Solution-Annealing — U Bend Stainless Steel Tube Solution Annealing

Stainless Steel U bend Tube Export Record

Export ASME SA213 TP316L U bend Tubes, OD 25.4mm, WT 2.11mm Total in 9800KGS.

Export ASME SA213 TP304L U bend Tubes, OD 25.4mm, WT 2.11mm Total in 5900KGS.

Export ASME SA213 TP321 U bend Tubes, OD 25.4mm, WT 2.11mm Total in 25000KGS.

Export ASME SA213 TP310S U bend Tubes, OD 25.4mm, WT 2.1mm, ST Length 3615mm, Total 710Pcs

AFRICA
  Nigeria
  Algeria
  Angola
  South Africa
  Libya
  Egypt
  Sudan
  Equatorial Guinea
  The Republic Of Congo
  Gabon

NORTH AMERICA
  USA
  Canada
  Mexico
  Panama
  Costa Rica
  Puerto Rica
  Trinidad And Tobago
  Jamaica
  Bahamas
  Denmark

EUROPE
Russia
  Norway
  Germany
  France
  Italy
  UK
  Spain
  Ukraine
  Netherland
  Belgium
  Greece
  Czech Republic
  Portugal
  Hungary
  Albania
  Austria
  Switzerland
  Slovakia
  Finland
  Ireland
  Croatia
  Slovenia
  Malta

ASIA
India
  Singapore
  Malaysia
  Indonesia
  Thailand
  Vietnam
  South Korea
  Japan
  Sri Lanka
  Maldives
  Bangladesh
  Mayanmar
  Taiwan
  Cambodia
SOUTH AMERICA
Argentina
  Bolivia
  Brazil
  Chile
  Venezuela
  Colombia
  Ecuador
  Guyana
  Paraguay
  Uruguay