17-4 PH Stainless Steel 630 Stainless Steel ASTM A564 ASTM A693 17-4 PH AISI 630  S17400 Stainless Steel Pipe
  • 17-4 PH Stainless Steel 630 Stainless Steel ASTM A564 ASTM A693 17-4 PH AISI 630  S17400 Stainless Steel Pipe

ASTM A564 Alloy 17-4 PH AISI 630 is a precipitation hardening martensitic stainless steel with Cu additions. The grade combines high strength, hardness (up to 300°C / 572°F) and corrosion resistance, combining high strength and post heat treatment hardness with excellent corrosion resistance that, in tests, proved superior to standard grades such as 420, 431 and 410. In fact, the corrosion resistance of 17-4PH is comparable with that of Grade 304.

Mechanical properties can be optimized with heat treatment. Very high yield strength up to 1100-1300 MPa (160-190 ksi) can be achieved. The grade should not be used at temperatures above 300°C (572°F) or at very low temperatures. It has adequate resistance to atmospheric corrosion or in diluted acids or salts where its corrosion resistance is equivalent to grade 304 or 430. chromium-copper stainless steel standardised as UNS S17400, 17-4PH is highly resistant to stress corrosion, has good machinability, short-term, low temperature heat treatments that minimise warpage and scaling, and is considered to be more cost effective than many high nickel non-ferrous alloys.

Due to the high strength of 17-4PH, its main use is in aerospace and other high technology industries such as offshore, in gears, valves, turbine blades, nuclear waste casks, moulding dies and shafts, as well as having been tested in the petrochemical, petroleum, paper, dairy and food processing industries, and in such applications as boat shafting. The unique combination of properties within 17-4PH makes this alloy an effective solution to many design and production problems.Standard Specification:

ASTM A564 Standard Specification for Hot-Rolled and Cold-Finished Age-Hardening Stainless Steel Bars and Shapes
ASTM A693 Standard Specification for Precipitation-Hardening Stainless and Heat-Resisting Steel Plate, Sheet, and Strip

Applications
Standards
Corrosion Resistance
Chemical Composition
Mechanical Properties
Physical Properties
Heat Treatment
Processing
Welding
Machining

ASTM A564 S17400 17-4 PH Stainless Steel Chemical Composition

C.Mn.P.S.Si.Cr.Ni.Cu. 
0.07%
max.
1.00%
max.
0.040%
max.
0.030%
max.
1.00%
max.
15.00-
17.50%
3.00-
5.00%
3.00-
5.00%
 

1.4542 Chemical Composition:

1.4542
X5CrNiCuNb16-4
CSiMnPSCrMoNiV
min. 15.0 3.0  
max.0.070.71.00.0250.01517.00.65.0  

17-4 PH Stainless Steel 630 Stainless Steel Density Specific Gravity: 7.78 (kg/dm³)

17-4 PH Stainless Steel 630 Stainless Steel Application

  • Variety of springs and washers
  • Aerospace parts
  • Heat exchangers
  • Power boilers
  • High strength/ high temperature conditions
  • Chemical processing equipment

17-4 PH Stainless Steel 630 Stainless Steel Corrosion Resistance

17-4PH stainless steel has excellent corrosion resistance. Corrosion tests and service experience have shown that in all aged conditions it is superior to standard hardenable stainless steel grades such as 420, 431 and 410. Its corrosion resistance is comparable to grade 304 Stainless

17-4 PH Stainless Steel 630 Stainless Steel Solution Annealing

As supplied 17-4PH is usuall in the solution treated condition (Condition A). It can be heat treated at different temperatures to offer a wide range of properties.

17-4 PH Stainless Steel 630 Stainless Steel Welding

Arc and resistance welding processes used on standard grades of stainless steel are applicable to 17-4PH stainless steel. The low hardness enables sections, up to 100mm, to be welded without requiring pre heating.

17-4 PH Stainless Steel 630 Stainless Steel Fabrication

17-4PH Condition is suitable for limited cold forming, H1100, H1150 and overaged conditions are more suitable when severe cold forming is required.

17-4 PH Stainless Steel 630 Stainless Steel Machining

17-4PH Condition has machining characteristics similar to stainless grades 302, 304 and 410. The high hardness and strength in Condition H900 is the most difficult to machine and the material should be machined at 60% of the rate which is used for Condition A.

17-4 PH Stainless Steel 630 Stainless Steel Nitriding

To increase the resistance to surface wear, with a slight decrease in corrosion resistance, 17-4PH stainless steel can be nitrided. An approximate hardness of 64/67HRc can be achieved, with a surface hardness depth of up to 0.15mm when nitrided at 540°C, while still maintaining a high core strength.

17-4 PH Stainless Steel 630 Stainless Steel
17-4 PH Stainless Steel 630 Stainless Steel
17-4 PH Stainless Steel 630 Stainless Steel
Stainlesss-Steel-Pipe-PMI-Testing

17-4 PH 630 Stainless Steel Tube Export Countries

MIDDLE EAST 
 Saudi Arabia
  Iran
  Iraq
  UAE
  Qatar
  Bahrain
  Oman
  Kuwait
  Turkey
  Yemen
  Syria
  Jordan
  Cyprus
AFRICA
  Nigeria
  Algeria
  Angola
  South Africa
  Libya
  Egypt
  Sudan
  Equatorial Guinea
  The Republic Of Congo
  Gabon

NORTH AMERICA
  USA
  Canada
  Mexico
  Panama
  Costa Rica
  Puerto Rica
  Trinidad And Tobago
  Jamaica
  Bahamas
  Denmark
EUROPE  
Russia
  Norway
  Germany
  France
  Italy
  UK
  Spain
  Ukraine
  Netherland
  Belgium
  Greece
  Czech Republic
  Portugal
  Hungary
  Albania
  Austria
  Switzerland
  Slovakia
  Finland
  Ireland
  Croatia
  Slovenia
  Malta
ASIA  India
  Singapore
  Malaysia
  Indonesia
  Thailand
  Vietnam
  South Korea
  Japan
  Sri Lanka
  Maldives
  Bangladesh
  Mayanmar
  Taiwan
  Cambodia
SOUTH AMERICA 
 Argentina
  Bolivia
  Brazil
  Chile
  Venezuela
  Colombia
  Ecuador
  Guyana
  Paraguay
  Uruguay

Related Products