EN 10217-7 2005 is for “Welded steel tubes for pressure purposes – Technical delivery conditions”. It covers a number of austenitic and duplex stainless steel. The mechanical properties are summarised in the table below. This article is not a substitute for the full standard. Steel grade Proof strength min MPA Tensile strengthMPa Elongation A min % Resistance to intergranular corrosion Steel name Steel number Rp0.2 Rp1.0 Rm long trans Austenitic X2CrNi18-9 1.4307 180 215 470/670 40 35 Yes X2CrNi19-11 1.4306 180 215 460/680 40 35 Yes X2CrNiN18-10 1.4311 270 305 550/760 35 30 Yes X5CrNi18-10  1.4301 195 230 500/700 40 35 Yes* X6CrNiTi18-10 1.4541 200 235 500/730 35 30 Yes X6CrNiNb18-10 1.4550 205 240 510/740 35 30 Yes X2CrNiMo17-12-2 1.4404 190 225 490/690 40 30 Yes X5CrNiMo17-12-2 1.4401 205 240 510/710 40 30 Yes* XCrNiMoTi17-12-2 1.4571 210 245 500/730 35 30 Yes X2CrNiMo17-12-3 1.4432 190 225 490/690 40 30 Yes X2CrNiMoN17-13-3 1.4429 295 330 580/800 35 30 Yes…

DIN 17459 specifies technical delivery conditions for seamless circular tubes made from high temperature austenitic stainless steel as specified in table. 1. Such stainless steel tube are intended primarily to be used in high-pressure applications where elevated temperature and high mechanical stresses are involved (e.g. in the construction of pressure boilers, pressure vessels, pipelines, and in the chemical industry). Material Chemical composition (%) degignation number C Si Mn P S Ni Cr Mo Ni others X 6 CrNi 18 11 1.4948 0.04 to 0.08 ≤0.75 ≤2.0 0.035 0.015 17.0 to 19.0 – 10.0 to 12.0   X 3 CrNiN 18 11 1.4949 ≤0.04 ≤0.75 ≤2.0 0.035 0.015 0.10 to 0.18 17.0 to 19.0 0.50 to 0.60 9.5 to 11.5   X 8 CrNiTi 18 10 1.4941 0.04 to 0.10 ≤0.75 ≤2.0 0.035 0.015 17.0 to 18.5 – 9.5 to 11.5 Ti: ≥5 x %Cto ≤  0.80B: 0.0015 to 0.0050 X6CrNiMo 17 13 1.4919 0.04 to 0.08 ≤0.75 ≤2.0 0.035…

The table shown is based on the reference data presented in EN 10088-1. Only a sample of the information available is shown. This is intended to show the scope of information available through representative figures for the most commonly used stainless steel tube types. A separate table indicates some of the grades that have been grouped together.Physical Properties Table Steel Types (AISI) Density Modulus Expansion Conductivity Specific Heat Resistivity . . 20C 400C . . . . Ferritic stainless steels 410S 7700 220 195 10.5 30 460 0.60 430 7700 220 195 10.0 25 460 0.70 444 7700 220 195 10.4 23 430 0.8 Martensitic and precipitation hardening stainless steels 410 7700 215 190 10.5 30 460 0.60 440 7700 215 190 10.4 15 430 0.8 630 7800 200 170 10.9 16 500 0.71 Austenitic stainless steel 304 7900 200 172 16.0 15 500 0.73 316 8000 200 172 16.0 15 500 0.75 ‘6%Mo’ 8000…

ASTM A595 Standard Specification for Steel Tubes, Low-Carbon or High-Strength Low-Alloy, Tapered for Structural Use covers three grades of seam-welded, round, tapered steel tubes for structural use. Grades A and B are of low-carbon steel or high-strength low-alloy steel composition and Grade C is of weather-resistance steel composition. The tube steel shall be hot-rolled aluminum-semikilled or fine-grained killed sheet or plate manufactured by one or more of the following processes: open-hearth, basic-oxygen, or electric-furnace. The tubes shall be made from trapezoidal sheet or plate that is preformed and then seam welded. They shall be brought to final size and properties by roll compressing cold on a hardened mandrel. A tensile test shall be done to determine the yield strength and the ultimate tensile strength of the tubes. 1.1 This specification covers three grades of seam-welded, round, tapered steel tubes for structural use. Grades A and B are of low-carbon steel or high-strength low-alloy steel composition and Grade C…

ASTM A790 covers seamless and straight-seam welded ferritic/austenitic duplex stainless steel pipe for general corrosive service, with particular emphasis on resistance to stress corrosion cracking. The pipe shall be made by the seamless or an automatic welding process, with no addition of filler metal in the welding operation. Heat analysis shall be made to determine the percentages of the elements specified. Tension tests, hardening tests, flattening tests, hydrostatic test and nondestructive electric tests shall be made to conform to the specified requirements. This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. This specification covers seamless and straight-seam welded ferritic/ austenitic stainless steel pip intended for general corrosive service, with particular emphasis on resistance to stress corrosion cracking. These steel are susceptible to embrittlement if used for prolonged periods at elevated temperatures. Optional supplementary requirements…

DSTU B A.3.2-12:2009 SSBP. Ventilation systems. Zagalni vimogi DSTU GOST 166:2009 (ISO 3599-76) Calipers. Technical specifications ( GOST 166-89 (ISO 3599-76), IDT) DSTU EN 473:2012 Non-invasive control. Qualification and certification of personnel. General provisions ( EN 473 :2008, IDT) DSTU 2680-94 Seamless rolled pipes made of steel and alloys. Terminology and identification of surface defects DSTU 2841-94 ( GOST 27809-95 ) Chavun i steel. Methods of spectrographic analysis DSTU 3124-95 Pipes made of steel and alloy. Bind and preparation of samples for the chemical warehouse. Basic provisions DSTU 4179-2003 Metal vibrating tapes. Technical skills ( GOST 7502-98 , MOD) DSTU GOST 6507:2009 Micrometers. Specifications DSTU 7238:2011 Safety standards system. Create a collective zakhist for the working people. Zagalni vimogi ta classification DSTU 7239:2011 Safety standards system. Assign an individual zakhist. Zagalni vimogi ta classification DSTU ISO 7438:2005 Metal materials. Testing for zgin (ISO 7438:1985, IDT) DSTU ISO 8496-2002 Metal materials. Trumpet. Testing for pulling out the rings with two parallel rods (ISO 8496:1988, IDT) DSTU GOST 12344:2005 Alloyed and high-alloyed steel. Methods for designing vugletsiu ( GOST 12344-2003 ,…

Inspection of the outer surface of pipes is carried out visually without the use of magnifying means. The internal surface of pipes with an internal diameter of 70 mm or more is inspected using a periscope or videoscopic systems. It is allowed to inspect the inner surface of pipes without the use of instruments, using lighting devices at both ends of the pipe against the light. For pipes with an internal diameter of less than 70 mm, as well as pipes with an internal diameter of 70 mm or more that have not been inspected by a periscope, the manufacturer guarantees that the internal surface of the pipes meets the requirements of these specifications based on satisfactory results of 100% ultrasonic inspection. The classification of defects is carried out in accordance with DSTU 2680 (OST 14-82 [ 18 ]). The depth of defects is checked after filing and subsequent measurement. The wall…

In the field of stainless steel, usually 304 is called TP304, 304L is called 304L, 316L is called TP316L. For example: ASTM A312 TP304, ASME SA213 TP304L, ASME SA213 TP316L. So what does “TP” mean? TP stands for Type. The reason is AISI(American Iron and Steel Institute) Classifies Stainless Steel in Type. For the same reason, sometimes 304, 304, L316L, will be called AISI 304, AISI 304L, AISI 316L.

OD: 17.15 – 508mm (3/8 INCH to 20 INCH)WT: 0.5 – 60 mm, Schedule 10s, 20, 40s, 40, 60, 80s, 80, 100, 120, 140, 160, XXH.Production Capacity: 500 MT/Month Guanyu Tube is specialized manufacturer of ASTM A312 TP304, ASTM A312 TP304L, ASTM A312 TP316, ASTM A312 TP316L, ASTM A312 TP321, ASTM A312 TP310S, ASTM A312 TP304 TP304L TP304H TP316 TP316L TP317L TP321 TP316Ti TP347 TP347H TP310S TP309S Stainless Steel Pipe Supplier. This is issued under the fixed designation ASTM A312; the number immediately following the designation indicates the year of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A superscript epsilon indicates an editorial change since the last revision or reapproval. This covers seamless, straight-seam and heavily cold worked welded austenitic stainless steel pipe for high-temperature and general corrosive service. When the impact test criterion for a low-temperature service would be…

Chemical Composition of ASTM A213 / ASME SA 213 317 317L 317LM 317LMN Stainless Steel Grade C Mn P Sulphur Si Cr Nickel Mo N Cu Weight % 317 S31700 18.00 11.00 3.00 Min.   0.08 2.00 0.045 0.030 1.00 20.00 15.00 4.00 Max. 317L S31703 18.00 11.00 3.00 Min. 0.035 2.00 0.045 0.030 1.00 20.00 15.00 4.00   Max. 317LM S31725 18.00 13.50 4.00   Min.   0.03 2.00 0.045 0.030 1.00 20.00 17.50 5.00 0.20 0.75 Max 317LMN S31726 17.00 13.50 4.00 0.10   Min. 0.03 2.00 0.045 0.030 1.00 20.00 17.50 5.00 0.20 0.75 Max. EN 10216-5 1.4439 16.50 12.50 4.00     Min. 0.030 2.00 0.040 0.015 1.00 18.50 14.50 5.00     Max. EN 10217-7 1.4438 17.50 13.00 3.00     Min. 0.030 2.00 0.045 0.030 1.00 19.50 16.00 4.00     Max. Mechanical Properties of 317 317L Stainless Steel Tubes       Tensile…

Checmical Composition of ASME SA213 304 304L 304H and EN 10216-5 1.4301 1.4307 1.4948 Grade – C Mn Si P S Cr Mo Ni N 304/S30400 min.max. -0.08 -2.0 -1.00 -0.045 -0.030 18.0-20.0 – 8.0-11.0 – EN 10216-5 1.4301 min.max. -0.07 -2.0 -1.00 -0.040 -0.015 17.00-19.5 – 8.0-10.5 -0.11 304L/S30403 min.max. -0.035 -2.0 -1.00 -0.045 -0.030 18.0-20.0 – 8.0-12.0 – EN 10216-5 1.4307 min.max. -0.030 -2.0 -1.00 -0.040 -0.015 17.5-19.5 – 8.0-10.0 -0.11 304H /S30409 min.max. 0.04-0.10 -2.0 -1.00 -0.045 -0.030 18.0-20.0 – 8.0-11.0 – EN 10216-5 1.4948 min.max. 0.04-0.08 -2.0 -1.00 -0.035 -0.015 17.0-19.0 – 8.0-11.0 -0.11 TP304L General PropertiesTP304L Chemical CompositionTP304L Resistance to CorrosionTP304L Physical PropertiesTP304L Mechanical PropertiesTP304L WeldingTP304L Heat TreatmentTP304L Cleaning304/304L/304LN/304H Tubing and Pipe304/304L Stainless Steel Tubing

We are specialized manufacturer of ASME SA249 ASTM A249 TP304, ASTM A249 TP304L, ASTM A249 TP304H, ASTM A249 TP316, ASTM A249 TP316L, ASTM A249 TP316H, ASTM A249 TP316Ti, ASTM A249 TP321 TP321H, ASTM A249 TP309H TP309S, ASTM A249 TP310S TP 310H, ASTM A249 TP347 Welded Tubes and ASTM A249 Welded Pipe. What is ASTM A249 ASME SA249? ASTM A249 is specifies standard specification for nomina wall thickness welded tubes and heavily cold worked welded tubes made from the austenitic steel with various grades intended for such use as a boiler, superheater, heat exchanger, or condenser tubes. Heat and product analysis shall conform to the requirements as to chemical composition for carbon, manganese, phosphorous, sulfur, silicon, chromium, nickel, molybdenum, nitrogen, copper, and others. All materials shall be furnished in the heat-treated condition in accordance with the required solution temperature and quenching method. ASTM A249 Tubing Test Items When the final heat treatment is in a continuous furnace, the number…

PT Test Standard International Organization for Standardization (ISO) ISO 3059, Non-destructive testing – Penetration testing and magnetic particle testing – Viewing conditions ISO 3452-1, Non-destructive testing. Penetrant testing. Part 1. General principles ISO 3452-2, Non-destructive testing – Penetrant testing – Part 2: Testing of penetrant materials ISO 3452-3, Non-destructive testing – Penetrant testing – Part 3: Reference test blocks ISO 3452-4, Non-destructive testing – Penetrant testing – Part 4: Equipment ISO 3452-5, Non-destructive testing – Penetrant testing – Part 5: Penetrant testing at temperatures higher than 50 °C ISO 3452-6, Non-destructive testing – Penetrant testing – Part 6: Penetrant testing at temperatures lower than 10 °C ISO 10893-4: Non-destructive testing of steel tubes. Liquid penetrant inspection of seamless and welded steel tubes for the detection of surface imperfections. ISO 12706, Non-destructive testing – Penetrant testing – Vocabulary ISO 23277, Non-destructive testing of welds – Penetrant testing of welds – Acceptance levels European Committee for Standardization (CEN) EN 1371-1, Founding – Liquid penetrant inspection…

What is ASTM A269 and ASTM A312 / ASME SA312? ASTM A269 / A269M Standard Specification for Seamless and Welded Austenitic Stainless Steel Tubing for General Service ASTM A312 / A312M Standard Specification for Seamless, Welded, and Heavily Cold Worked Austenitic Stainless Steel Pipe StandardItem ASTM A213 ASTM A269 ASTM A312 Grade 304  304L 304H   304N  304LN316  316L 316Ti   316N  316LN321  321H   310S   310H  309S317  317L 347 347H 304  304L 304H 304N 304LN316  316L 316Ti 316N  316LN321 321H  310S 310H  309S317  317L 347 347H 304  304L 304H   304N  304LN316  316L 316Ti   316N  316LN321  321H  310S   310H  309S317  317L  347 347H Yield Strength(Mpa) ≥170；≥205 ≥170；≥205 ≥170；≥205 Tensile Strength(Mpa) ≥485；≥515 ≥485；≥515 ≥485；≥515 Elongation(%) ≥35 ≥35 ≥35 Hydrostatic Test OD(mm) Pressure max(MPa) OD(mm) Pressure max(MPa) OD(mm) Pressure max(MPa) D<25.4, 7Mpa D<25.4, 7Mpa D≤88.9, 17MPa 25.4≤D<38.1, 10Mpa 25.4≤D<38.1, 10Mpa 38.1≤D<50.8, 14Mpa 38.1≤D<50.8, 14Mpa 50.8≤D<76.2， 17MPa 50.8≤D<76.2， 17MPa D>88.9, 19MPa 76.2≤D<127， 24MPa 76.2≤D<127， 24MPa D≥127, 31Mpa D≥127, 31Mpa P=220.6t/D…

　 　 C C Si Si Mn Mn P P S S Cr Cr Ni Ni Mo Mo N N Cu Cu Ti Ti Nb Nb 　 　 min max min max min max min max min max min max min max min max min max min max min max min max DIN 17456 1.4301 0.00 0.070 0.00 1.00 0.00 2.00 0.00 0.045 0.00 0.015 17.00 19.00 8.00 10.50 　 　 　 　 　 　 　 　 　 　 DIN 17456 1.4306 0.00 0.030 0.00 1.00 0.00 2.00 0.00 0.045 0.00 0.015 18.00 20.00 10.00 12.00 　 　 　 　 　 　 　 　 　 　 DIN 17456 1.4311 0.00 0.030 0.00 1.00 0.00 2.00 0.00 0.045 0.00 0.015 17.00 19.50 8.50 11.50 　 　 　 　 　 　 　 　 　 　 DIN 17456 1.4541 0.00 0.080 0.00 1.00 0.00 2.00 0.00 0.045 0.00 0.015 17.00 19.00 9.00 12.00…

　 　 C C Si Si Mn Mn P P S S Cr Cr Ni Ni Mo Mo N N Cu Cu Ti Ti Nb Nb 　 　 min max min max min max min max min max min max min max min max min max min max min max min max J3459 SUS304TP 0.00 0.080 0.00 1.00 0.00 2.00 0.00 0.040 0.00 0.030 18.00 20.00 8.00 11.00 　 　 　 　 　 　 　 　 　 　 J3459 SUS304HP 0.040 0.100 0.00 0.75 0.00 2.00 0.00 0.040 0.00 0.030 18.00 20.00 8.00 11.00 　 　 　 　 　 　 　 　 　 　 J3459 SUS304LTP 0.00 0.030 0.00 1.00 0.00 2.00 0.00 0.040 0.00 0.030 18.00 20.00 9.00 13.00 　 　 　 　 　 　 　 　 　 　 J3459 SUS310STP 0.00 0.080 0.00 1.50 0.00 2.00 0.00 0.040 0.00 0.030 24.00 26.00 19.00 22.00 　 　 　 　…

ASTM B111 Standard Specification for Copper and Copper-Alloy Seamless Condenser Tubes and Ferrule StockASTM A213/A213M Standard Specification for Seamless Ferritic and Austenitic Alloy-Steel Boiler, Superheater, and Heat-Exchanger TubesASTM A269/A269M Standard Specification for Seamless and Welded Austenitic Stainless Steel Tubing for General ServiceASTM A249 – A249/A249M Specification fors Welded Austenitic Steel Boiler, Superheater, Heat Exchanger, and Condenser TubesASTM A179 – A179/A179M – Specification for Seamless Cold-Drawn Low-Carbon Steel Heat Exchanger Tubes and Condenser TubesASTM A214 – A214/A214M Specification for Electric-Resistance-Welded Carbon Steel Heat-Exchanger and Condenser TubesASTM A851 – A851 Specification for High-Frequency Induction Welded, Unannealed, Austenitic Steel Condenser Tubes Condenser TubeAdvantage of Stainless Steel tube in CondenserASTM Standard for Heat-Exchanger and Condenser TubesCondenser Tube SpecificationsDisadvantage of stainless steel tube in condenserWhy does the condenser need to use stainless steel tubes?Large Steam System Condensers

Grade EN / UNS Sizes Tolerances Testing 1.4749/S44600 EN ISO 1127Metric: Not standardized=NSI/ASME B 36.19 EN ISO 1127 ASTM A213/A 450 1.4959/N08811 / N08810 ANSI/ASME B 36.19 Cold finished:ASTM B 407Hot finished: ASTM A999 Cold finished:ASTM B 407Hot finished: ASTM B 407 1.4835/S30815/253MA1.4854/S35315/353MA ANSI/ASME B 36.19 ASTM A999 ASTM A312/A 999

Stainless steel are iron-based alloys usually containing at least 11.5% chromium. Other elements, Nickel being the most Important, may be added in combination with chromium to obtain special properties. Stainless steel are highly resistant to corrosive attack and to oxidation at high temperature. in general, corrosion resistance and oxidation resistance increase progressively, though not proportionately, with the increase in chromium content. Stainless steel pipe and tubing are used for a variety of reasons: to resist corrosion and oxidation, to resist high temperature, for cleanliness and low maintenance costs, and to maintain the purity of materials which come In contact with stainless. The inherent characteristics of stainless steel tubing permits the design of thin wall piping systems without fear of early failure due to corrosion. The use of fusion welding to join such piping eliminates the need for threading. Type 304 stainless steel is the most widely used analysis for general corrosion resistant tubing and pipe applications, it is used in…

EN Standards: EN European Standard for Stainless Steel European EN Standard Grade Summary European Dimensional Tolerance Standard for Stainless Steel EN 10090 Chemical Composition of Valve Steel BS 970 Stainless Steel Chemical Composition BS 3100 1991 Cast Steel Chemical Composition BS 3100 Chemical Composition of Stainless Steel BS 1449-2 Chemical Composition of Stainless Steel BS Aerospace S100 Chemical Composition Mechanical Properties BS Aerospace S500 Chemical Composition Mechanical Properties EN 10204 Test Certificates for Stainless Steel EN 10302 Chemical Composition of Creep Resisting Steel EN 10302 Mechanical Properties of Creep Resisting Steel Tolerance to EN 10296-2 Welded Stainless Steel Tubes EN 10296-2 Stainless Steel Chemical Composition EN 10296-2 Stainless Steel Welded Tubes Mechanical Properties Chemical Compositions of Stainless Steel to EN 10297-2 EN 10297-2 Mechanical Properties of Stainless Steel Tubes Tolerances to EN 10297-2 for Seamless Stainless Steel Tubes EN 10269 Room Temperature Mechanical Properties of Stainless Steel EN 10269 Elevated…

ASTM Standards: ASTM Standard for Stainless Steel Carbon Steel Pipe Standard ASTM BS DIN Sweden ASTM B265 Titanium Alloy Properties ASTM B265 Titanium Alloy Chemical Composition ASTM A48 Standard Specification for Gray Iron Castings ASTM A53 Standard Steel Pipe Black Hot-Dipped Zinc-Coated ASTM A53 Pipe ASME SA53 Steel Pipe Maximum Working Pressure-ASTM A53 B Carbon Steel Pipes ASTM A 53 & ASTM A 106. Welded and Seamless Black Pipes Seamless Pipe from Carbon Steel Intended for Operation by High Temperature ASTM A105 Standard for Forgins Carbon Steel Piping ASTM A106 Carbon Steel Pipe High-Temperature Service ASTM A106 / A106M – 08 Standard Specification for Seamless Carbon Steel Pipe for High-Temperature Service ASTM A134 Standard for Steel Pipe Electric-Fusion Arc-Welded ASTM A134 Specification for Steel Pipe Electric-Fusion Arc-Welded ASTM A135 Standard for Electric-Resistance-Welded Steel Pipe ASTM A139 Specification of Electric-Fusion-Welded Steel Pipe ASTM A139 Standard Electric-Fusion Arc-Welded Steel Pipe ASTM A148…

Guanyu Tube is specialized manufacturer of ASTM A269 TP304, ASTM A269 TP304L, ASTM A269 TP316, ASTM A269 TP316L, ASTM A269 Tubing in China. Delivery condition in Bright Annealing or Annealing Pickling and Outside surface Polishing. ASTM A269 Tubing mainly include ASTM A269 TP316 Stainless Steel Instrumentation Tubing, ASTM A269 TP316L Stainless Steel Instrument Tubing, Stainless Steel Hydraulic Tubing. ASTM A269 is issued under the fixed designation ASTM A269, the number immediately following the designation indicates the year of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A superscript epsilon indicates an editorial change since the last revision or reapproval. This specification covers grades of nominal-wall thickness, stainless steel tubing for general corrosion-resisting and low-or high-temperature service, as designated in Table 1. The tubing sizes and thickness usually furnished to this specification are 1⁄4 in. (6.4 mm) in inside diameter and…

ASTM A269 and ASTM A249 are both workable for Welded Stainless Steel Tubes and Pipe. ASTM A249 / A249M Standard Specification for Welded Austenitic Steel Boiler, Superheater, Heat-Exchanger, and Condenser Tubes. ASTM A269 / A269M Standard Specification for Seamless and Welded Austenitic Stainless Steel Tubing for General Service. ASTM A249 ASTM A269 Comparison Chart ASTM A249 and ASTM A269 specifications are two standards for Austenitic stainless steel tubes, there are the same requirements in technical, also they have some differences. Specification ASTM A249 ASTM 269 Tube Manufacturing Welded Welded And Seamless Application BoilerSuperheaterHeat-ExchangerCondenser General Service Sizes OD: maximum 304.8 mmWall Thickness: 0.4 – 8.1 mm Inside Diameter: minium 3.4 mmWall Thickness: 0.51 mm ASTM / ASME ASTM A249 / A249MASME SA249 ASTM A269 / A269M Test Flange Test Flange Test A249 VS A269 Scope Of Application ASTM A249 welded tubes are for boiler, super heater, heat exchanger, condenser system, the…

ASTM A789 ASME SA 789 S31803 S32205 S32101 S32750 S32760 S32304 S31500 S31260 Seamless Tubes Manufacturer

ASTM A213 ASME SA213 TP304 TP304L TP309S TP310S TP316L TP316Ti TP321 TP317L TP347H Heat Exchanger Tube

Stainless Steel Tube Specifications Table of Contents： ASTM Stainless Steel Tube Specifications: Iron and Steel Products Steel Piping, Steel Tubing, Fittings ASTM A1016 Standard Specification for General Requirements for Ferritic Alloy Steel, Austenitic Alloy Steel, and Stainless Steel Tubes ASTM A999 Standard Specification for General Requirements for Alloy and Stainless Steel Pipe A 213 / A 213M Seamless ferritic and austenitic alloy steel boiler, superheater and heat exchanger tubes SA 240 / SA 240M Standard Specification for Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels and for General Applications SA 249 / SA 249M Standard Specification for Welded Austenitic Steel Boiler, Superheater, Heat Exchanger, and Condenser Tubes A 268 / A268M Seamless and welded ferritic and martensitic stainless steel tubing for general service A 269 / A 269M Seamless and welded austenitic stainless steel tubing for general service A 270 / A 270M Seamless and welded…

ASTM B163 N02200 N02201 N04400 N06600 N06601 N06690 N08800 N08810 N08811 N08825 N08020 N06025 U Bend Nickel Alloy Tubes

Standards for seamless stainless steel tube & pipe: Standard Catagory HydraulicInstrumentationHeat exchangersPipe ASME / ANSIISO & metricHigh TemperatureSpecification Standards for Heat Exchanger TubesASME – American Society of Mechanical EngineersASME Specifications Stainless SteelStainless Steel Pipe SpecificationDuplex Stainless Steel Pipe Specification Standard | Technical Term Abbreviation | Stainless Steel Glossary | World Society Shipping | International Phone Country Number | World Standards Full Name | Steel Metal Glossary | Standard Documents Format | Metals and Engineering Terms Glossary | Hot Dip Galvanizing Glossary Standard: ASTM A269 vs A312 Difference Between ASTM A269 and A312 Difference Between ASTM A213 and ASTM A269 Difference Between ASTM A213 and ASTM A312 Specification of Incoloy 825 UNS N08825 Seamless Tubes OCTG Casing Coupling NACE MR0175 and MR0103 Standards Carbon Steel Pipe Standard ASTM BS DIN Sweden EN 10095 Mechanical Properties of Stainless Steel EN 10088-3 Mechanical Martensitic and Precipitation Hardening EN 10088-3 Mechanical Properties of Ferritic Stainless Steel EN 10088-2 Mechanical Properties of Martensitic Stainless Steel EN 10088-2 Mechanical Properties of Ferritic Stainless Steel…