ASTM A671 EFW Steel Pipe for Atmospheric Temperatures
ASTM A671 Standard Specification for Electric-Fusion-Welded Steel Pipe for Atmospheric and Lower Temperatures covers standard requirements for electric-fusion-welded steel pipe with filler metal added, for atmospheric and lower temperatures. The steel pipe shall be fabricated from a pressure vessel quality plate of various analysis and strength levels. Several grades and classes of pipe shall be provided. Grade shall designate the type of plate used while class shall designate the type of heat treatment performed during pipe manufacture. Class shall be designated as to whether the weld is radiographically examined, and as to whether the pipe is pressure tested. Steel samples shall undergo tension and transverse guided weld bend tests and conform to the specified mechanical requirements..
This specification covers electric-fusion-welded steel pipe with filler metal added, fabricated from pressure vessel quality plate of several analyses and strength levels and suitable for high-pressure service at atmospheric and lower temperatures. Heat treatment may or may not be required to attain the desired properties or to comply with applicable code requirements. Supplementary requirements are provided for use when additional testing or examination is desired.
The specification nominally covers pipe 16 in. [400 mm] in outside diameter or larger and of 1/4 in. [6 mm] wall thickness or greater. Pipe having other dimensions may be furnished provided it complies with all other requirements of this specification.
Several grades and classes of pipe are provided.
1.3.1 Grade designates the type of plate used as listed in 5.1.
1.3.2 Class designates the type of heat treatment performed during manufacture of the pipe, whether the weld is radiographically examined, and whether the pipe has been pressure tested as listed in 1.3.3.
1.3.3 Class designations are as follows (Note 1):
Class |
Heat Treatment on Pipe |
Radiography, see Section |
Pressure Test, see: |
10 |
none |
none |
none |
11 |
none |
9 |
none |
12 |
none |
9 |
8.3 |
13 |
none |
none |
8.3 |
20 |
stress relieved, see 5.3.1 |
none |
none |
21 |
stress relieved, see 5.3.1 |
9 |
none |
22 |
stress relieved, see 5.3.1 |
9 |
8.3 |
23 |
stress relieved, see 5.3.1 |
none |
8.3 |
30 |
normalized, see 5.3.2 |
none |
none |
31 |
normalized, see 5.3.2 |
9 |
none |
32 |
normalized, see 5.3.2 |
9 |
8.3 |
33 |
normalized, see 5.3.2 |
none |
8.3 |
40 |
normalized and tempered, see 5.3.3 |
none |
none |
41 |
normalized and tempered, see 5.3.3 |
9 |
none |
42 |
normalized and tempered, see 5.3.3 |
9 |
8.3 |
43 |
normalized and tempered, see 5.3.3 |
none |
8.3 |
50 |
quenched and tempered, see 5.3.4 |
none |
none |
51 |
quenched and tempered, see 5.3.4 |
9 |
none |
52 |
quenched and tempered, see 5.3.4 |
9 |
8.3 |
53 |
quenched and tempered, see 5.3.4 |
none |
8.3 |
60 |
normalized and precipitation heat treated |
none |
none |
61 |
normalized and precipitation heat treated |
9 |
none |
62 |
normalized and precipitation heat treated |
9 |
8.3 |
63 |
normalized and precipitation heat treated |
none |
8.3 |
70 |
quenched and precipitation heat treated |
none |
none |
71 |
quenched and precipitation heat treated |
9 |
none |
72 |
quenched and precipitation heat treated |
9 |
8.3 |
73 |
quenched and precipitation heat treated |
none |
8.3 |
Note 1—Selection of materials should be made with attention to temperature of service. For such guidance, Specification ASTM A20/A20M may be consulted.
1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. The inch-pound units shall apply unless the “M” designation of this specification is specified in the order.
ASTM Standards
ASTM A20/A20M Specification for General Requirements for Steel Plates for Pressure Vessels
ASTM A370 Test Methods and Definitions for Mechanical Testing of Steel Products
ASTM A435/A435M Specification for Straight-Beam Ultrasonic Examination of Steel Plates
ASTM A530/A530M Specification for General Requirements for Specialized Carbon and Alloy Steel Pipe
ASTM A577/A577M Specification for Ultrasonic Angle-Beam Examination of Steel Plates
ASTM A578/A578M Specification for Straight-Beam Ultrasonic Examination of Rolled Steel Plates for Special Applications
ASTM E110 Test Method for Indentation Hardness of Metallic Materials by Portable Hardness Testers
ASTM E165 Practice for Liquid Penetrant Examination for General Industry
ASTM E709 Guide for Magnetic Particle Testing
ASME Boiler and Pressure Vessel Code
SectionIX,WeldingQua
Keywords
bolting; chemical analysis; coated; marking on fasteners; plated, Alloy steel bolting materials--specifications, Carbon steel bolting materials--specifications, Carbon steel flanges / fittings / valves / parts-specification, High-temperature service applications steel bolting application, Nuts specification
|