EN 10217-7 1.4162 1.4462 1.4362 1.4410 1.4501 Țevi sudate din oțel inoxidabil
EN 10217-7 1.4162 1.4462 1.4362 1.4410 1.4501 Țevi sudate din oțel inoxidabil
EN 10217-7 1.4301 1.4307 1.4948 1.4541 1.4878 1.4550 1.4401 1.4405 1.4571 1.4438 1.4439 1.4833 1.4845 Tuburi sudate din oțel pentru aplicații sub presiune
We are EN 10217-7 1.4162 1.4462 1.4362 1.4410 1.4501 Welded Stainless Steel Pipes Manufacturer. is the material standard for stainless steel for tuburi sudate for presiune purposes. This new standard was first published in February 2005.
Included in the standard are compoziția chimică, delivery conditions and process route symbols, ambient temperatură mechanical properties, some additional optional tests (leak testing, flattening, drift expansion, bend and non-destructive testing) and some dimensional and toleranță requirements. ustenitic, and austenitic-ferritic oțel inoxidabil duplex grades are included in the range of grades specified in this standard. Only the chemical composition of the stainless steel tubing in the standard are listed in this article.
It is interesting to compare the grades listed in this standard with those in the standard for welded stainless steel tube for general engineering purposes EN 10296-2. See table below. The implication of this is that some grades can be used for presiune purposes which cannot be used for general purposes. It is unlikely that this anomaly was the intention of the standards writers.
The chrome and nickel contents are quoted to 2 decimal places in EN 10217-7 whereas EN 10296-2 quotes only 1 dp. The reason for this is not clear.
For grade 1.4307, the composition differs from that inEN 10296-2, in that the Ni content is 8.00/10.00 compared to 8.0/10.5. This reflects the difference in the flat products standards to which the original strip would be made:
EN 10088-2 – Flat products for general purposes 1.4307 Ni 8.0/10.5
EN 10028-7 Flat products for pressure purposes 1.4307 Ni 8.00/10.00
The reason for these differences is not explained in the standard.
It might be expected that any steels appearing in EN 10028-7 Flat products for pressure purposes would appear in the comparable welded tube standard. This is not the case. The following grades in EN 10028-7 are not found in EN 10217-7:
Ferritic grades – 1.4003, 1.4516, 1.4510, 1.4521, 1.4520, 1.4509
Martensitic grades – 1.4313, 1.4418,1.4541
Austenitic grades – 1.4318, 1.4315, 1.4406, 1.4335, 1.4466, 1.4580, 1.4434, 1.4537
Duplex grades – 1.4507,1.4462 1.4162 1.4462 1.4362 1.4410 1.4501
Creep resisting steels – 1.4948, 1.4950, 1.4951, 1.4941, 1.4958, 1.4959, 1.4910, 1.4961
As an alternative to scanning down the list try the ‘find’ facility on your keyboard, using the ‘Ctrl’ and ‘F’ keys together. Type in the term you are looking for in the dialog box that then appears.
| APPLICATION | RO | S.S. | ASTM-ASME | DIN | NFA | GOST |
| Industria chimică | EN 10217-7 | 219711 219713 | A358-SA358 A312-SA312 A269 ASTM A928 | 17457 | 49147 | gost 11068-81 |
| Produse alimentare | EN 10217-7 | ASTM A270 | 11850 | 49249 | ||
| Tuburi de schimbător de căldură | EN 10217-7 | 219711 219713 | A 249–SA 249 | 17457 2818 | 49247 49244 | GOST 11068-81 |
| Linia de conducte | EN 10217-7 | A778 A269 | 17455 | 49147 | ||
| Apă potabilă | EN 10312 | DVGW541 | ||||
| Elemente decorative | EN 10296-2 | ASTM A554 | 17455 2395 | 49647 |
EN 10217-7 Compoziție chimică Tables
| Desemnare | Chemical composition (% by mass – max unless stated) | ||||||||||||
| Steel name | Steel No. | C | Si | Mn | P | S | Cr | Mo | Ni | Cu | N | Altele | |
| Austenitic steel | |||||||||||||
| X2CrNi18-9 | 1.4307 | 0.03 | 1.00 | 2.0 | 0.045 | 0.015 | 17.50 /19.5 | – | 8.0 /10.0 | – | 0.11 | – | |
| X2CrNi19-11 | 1.4306 | 0.03 | 1.00 | 2.0 | 0.045 | 0.015 | 18.00 /20.0 | – | 10.0 /12.0 | – | 0.11 | – | |
| X2CrNiN18-10 | 1.4311 | 0.03 | 1.00 | 2.0 | 0.045 | 0.015 | 17.00 /19.5 | – | 8.50 /11.5 | – | 0.12 /0.22 | – | |
| X5CrNi18-10 | 1.4301 | 0.07 | 1.00 | 2.0 | 0.045 | 0.015 | 17.00 /19.5 | – | 8.00 /10.5 | – | 0.11 | – | |
| X6CrNiTi18-10 | 1.4541 | 0.08 | 1.00 | 2.0 | 0.045 | 0.015 | 17.00 /19.0 | – | 9.00 /12.0 | – | – | Ti 5xC /0.70 | |
| X6CrNiNb18-10 | 1.4550 | 0.08 | 1.00 | 2.0 | 0.045 | 0.015 | 17.00 /19.0 | – | 9.00 /12.0 | – | – | Nb 10xC /1.00 | |
| X2CrNiMo17-12-2 | 1.4404 | 0.03 | 1.00 | 2.0 | 0.045 | 0.015 | 16.50 /18.5 | 2.0 /2.5 | 10.00 /13.0 | – | 0.11 | – | |
| X5CrNiMo17-12-2 | 1.4401 | 0.07 | 1.00 | 2.0 | 0.045 | 0.015 | 16.50 /18.5 | 2.0 /2.5 | 10.00 /13.0 | – | 0.11 | – | |
| XCrNiMoTi17-12-2 | 1.4571 | 0.08 | 1.00 | 2.0 | 0.045 | 0.015 | 16.50 /18.5 | 2.0 /2.5 | 10.50 /13.5 | – | – | Ti 5xC /0.70 | |
| X2CrNiMo17-12-3 | 1.4432 | 0.03 | 1.00 | 2.0 | 0.045 | 0.015 | 16.50 /18.5 | 2.5 /3.0 | 10.50 /13.0 | – | 0.11 | – | |
| X2CrNiMoN17-13-3 | 1.4429 | 0.03 | 1.00 | 2.0 | 0.045 | 0.015 | 16.50 /18.5 | 2.5 /3.0 | 11.00 /14.0 | – | 0.12 /0.22 | – | |
| X3CrNiMo17-13-3 | 1.4436 | 0.05 | 1.00 | 2.0 | 0.045 | 0.015 | 16.50 /18.5 | 2.5 /3.0 | 10.50 /13.0 | – | 0.11 | – | |
| X2CrNiMo18-14-3 | 1.4435 | 0.030 | 1.00 | 2.0 | 0.045 | 0.015 | 17.00 /19.0 | 2.5 /3.0 | 12.50 /15.0 | – | 0.11 | – | |
| X2CrNiMoN17-13-5 | 1.4439 | 0.03 | 1.00 | 2.0 | 0.040 | 0.015 | 16.50 /18.5 | 4.0 /5.0 | 12.50 /14.5 | – | 0.12 /0.22 | – | |
| X2CrNiMo18-15-4 | 1.4438 | 0.03 | 1.00 | 2.0 | 0.045 | 0.015 | 17.50 /19.5 | 3.0 /4.0 | 13.00 /16.0 | – | 0.11 | – | |
| X1NiCrMoCu31-27-4 | 1.4563 | 0.02 | 0.70 | 2.0 | 0.030 | 0.010 | 26.00 /28.0 | 3.0 /4.0 | 30.00 /32.0 | 0.70 /1.50 | 0.11 | – | |
| X1CrNiMoCu25-20-5 | 1.4539 | 0.02 | 0.70 | 2.0 | 0.030 | 0.010 | 19.00 /21.0 | 4.0 /5.0 | 24.00 /26.0 | 1.20 /2.00 | 0.15 | – | |
| X1CrNiMoCuN20-18-7 | 1.4547 | 0.02 | 0.70 | 1.0 | 0.030 | 0.010 | 19.50 /20.5 | 6.0 /7.0 | 17.50 /18.5 | 0.50 /1.00 | 0.18 /0.25 | – | |
| X1NiCrMoCuN25-20-7 | 1.4529 | 0.02 | 0.50 | 1.0 | 0.030 | 0.010 | 19.00 /21.0 | 6.0 /7.0 | 24.00 /26.0 | 0.50 /1.50 | 0.15 /0.25 | – | |
| Austenitic feritice oțel | |||||||||||||
| X2CrNiN23-4 | 1.4362 | 0.03 | 1.00 | 2.0 | 0.035 | 0.015 | 22.00 /24.0 | 0.10 /0.60 | 3.50 /5.50 | 0.10 /0.60 | 0.05 /0.20 | – | |
| X2CrNiMoN22-5-3 | 1.4462 | 0.03 | 1.00 | 2.0 | 0.035 | 0.015 | 21.00 /23.0 | 2.50 /3.50 | 4.50 /6.50 | – | 0.10 /0.22 | – | |
| X2CrNiMoN25-7-4 | 1.4410 | 0.03 | 1.00 | 2.0 | 0.035 | 0.015 | 24.00 /26.0 | 3.00 /4.50 | 6.00 /8.00 | – | 0.20 /0.35 | – | |
| X2CrNiMoCuWN25-7-4 | 1.4501 | 0.03 | 1.00 | 1.0 | 0.035 | 0.015 | 24.00 /26.0 | 3.00 /4.00 | 6.00 /8.00 | 0.50 /1.00 | 0.20 /0.30 | W 0.50 /1.00 | |
EN 10217 - 7 Țevi sudate din oțel pentru aplicații sub presiune. Condiții tehnice de livrare. Tuburi din oțel nealiat cu proprietăți specificate la temperatura camerei
EN 10217-7 Proprietăți mecanice pentru oțel inoxidabil
EN 10217-7 Compoziția chimică a țevilor din oțel inoxidabil
EN 10217-5/A1 Țevi sudate din oțel pentru aplicații sub presiune
Proprietăți mecanice la temperatura ambiantă pentru EN 10217-7
Proprietăți mecanice la temperatură ambiantă pentru BS EN 10253-3 și 10253-4
Proprietăți mecanice la temperatura ambiantă pentru EN 10216-5
Compoziția chimică a oțelurilor inoxidabile conform EN 10216-5
EN 10216-5 țevi din oțel inoxidabil