Zhejiang Guanyu Stainless Steel Tube Co., Ltd  
  Directory | Useful Tool | Sitemap | Contact US | Home

         

Standard

API 5L PSL 1 Pipe Mechanical Properties Tensile Strength






API 5L PSL 1 Pipe Mechanical Properties Table

Pipe Grade Pipe body of seamless and welded pipes
Weld seam of EW, 
SAW and COW pip
Yield strength
R10,5

MPa(psi)
minimum

Tensile strength
Rm

MPa(psi)
minimum
Elongation
Af

%
minimum
Tensile strength
Rm

MPa(psi)
minimum
L175 or A25 175 (25 400) 310 (45 000) c 310 (45 000)
L175P or A25P 175 (25 400) 310 (45 000) c 310 (45 000)
L210 or A 210 (30 500) 335 (48 600) c 335 (48 600)
L245R or BR 
L245 or B
245 (35 500) 415 (60 200) c 415 (60 200)
L290R or X42R 
L290 or X42
290 (42 100) 415 (60 200) c 415 (60 200)
L320 or X46 320 (46 400) 435 (63 100) c 435 (63 100)
L360 or X52 360 (52 200) 460 (66 700) c 460 (66 700)
L390 or X56 390 (56 600) 490 (71 100) c 490 (71 100)
L415 or X60 415 (60 200) 520 (75 400) c 520 (75 400)
L450 or X65 450 (65 300) 535 (77 600) c 535 (77 600)
L485 or X70 485 (70 300) 570 (82 700) c 570 (82 700)

aFor intermediate grades, the difference between the specified minimum tensile strength and the specified minimum yield strength for the pipe body shall be as given in the table for the next higher grade. 

bFor intermediate grades, the specified minimum tensile strength for the weld seam shall be the same value as was determined for the pipe body using footnote a). 

cThe specified minimum elongation, Af expressed in percent and rounded to the nearest percent, shall be as determined using the following equation;

where

C is 1 940 for calculations using SI units and 625 000 for calculations using USC units;

Axc is the applicable tensile test piece cross-sectional area, expressed in square millimetres (square inches), as follows:

----- for circular cross-section test pieces, 130 mm2 (0.20 in2) for 12,5 mm (0.500 in) and 8,9 mm (0.350 in) diameter test pieces; and 65 mm2(0.10 in2) for 6,4 mm (0.250 in) diameter test pieces;

------ for full-section test pieces, the lesser of a) 485 mm2 (0.75 in2) and b) the cross-sectional area of the test piece, derived using the specified outside diameter and the specified wall thickness of the pipe, rounded to the nearest 10 mm2 (0.01 in2);

----- for strip test pieces, the lesser of a) 485 mm2 (0.75 in2) and b) the cross-sectional area of the test piece, derived using the specified width of the test piece and the specified wall thickness of the pipe, rounded to the nearest 10 mm2(0.01 in2);

U is the specified minimum tensile strength, expressed in megapascals (pounds per square inch).

Related References:
API 5CT. Tubing
API 5L. Line Pipes
OCTG API 5L ASTM Line Pipes Specification
Chemical Composition for API 5L PSL 1 Pipes
Chemical Composition for API 5L PSL 2 Pipes
API 5L PSL 1 Pipe Mechanical Properties Tensile Strength
API 5L PSL 2 Pipe Mechanical Properties Tensile Strength
API 5L PSL 2 Pipes Impact Test Table
API 5L Steel Number Steel Designation Equivalent Table ISO 3138 EN 10027-2

TubingChina.com All Rights Reserved

Directory | Standard | Heat | Heat Exchanger | Temperature | Pressure | Corrosion | Hardness | Surface | Properties | Select Stainless Steel | Contact US

Useful Tools:

Stainless Steel Weight Calculator
Metals Weight Calculator
Nickel Alloy Weight Calculator
Copper Brass Alloy Weight Calculator
Copper Brass Alloy Sheet Plate Weight Calculator
Sheet Plate Weight Calculator
Hardness Conversion Calculator
Hardness Conversion Chart
Rockwell Brinell Vickers Shore Hardness Conversion Chart
Conversion Calculator
Length Weight Temperature Volume Pressure Calculater
Pipe Working Pressure Calculator
Pressure Conversion Converter
Round Bar Size Calculator
Gauge Sizes
Sheet Metal Gauge
Pipe Schedule
Nominal Pipe Size
ANSI Pipe Chart
Inch to mm Chart
Stainless Steel Pipe Sizes
Stainless Steel Tubing Sizes Chart
Stainless Steel L H Grade
Stainless Steel Density
Conversion of Stainless Steel
Nickel Alloy Grades Comparison Material Grade Chart Carbon Steel
Structural Steel Comparison Chart



Main Products:

BA Tube | AP Tube
Condenser Tubes Tubing
Stainless Steel Reheater Tube Superheater Tubes
Stainless Steel U bend Tube
Nickel Alloy U bend Tubes
Copper Alloy U Bend Tubes
Heat Exchanger Tube
Super Duplex Pipe
Nickel Alloy Tube
Brass Alloy Tubing
Copper Nickel Alloys Tubes
Stainless Steel Hollow Tube
Stainless Steel Oval Tubing
Stainless Steel Square Tubing
Stainless Steel Rectangular Tubing
Stainless Steel Capillary Tube
Duplex Stainless Steel Pipe
Seamless Stainless Steel Tubing
Corrugated Stainless Steel Tubing
Stainless Steel Twisted Tube
Polishing Stainless Steel Tubing
Stainless Steel Aircraft Tube
Stainless Steel Hydraulic Tubing
Stainless Steel Instrumentation Tubing
Stainless Steel Angle Iron Bar
Stainless Steel Mechanical Tube
Bright Annealing Stainless Tube
Heat resistant Stainless Steel
Stainless Steel Welded Pipe
Extruded Serrated Finned Tubes Integral Finned Tubes / Extruded Aluminum Finned Tubes
Brass Alloys Copper Nickel Alloy Integral Low Finned Tubes
HFW High Frequency Welded Helical Spiral Serrated Finned Tubes
Corrosion Resistant Stainless Steel
Corrosion Resistance Stainless Steel

Stainless Steel Tubing Pipe

304 Stainless Steel Pipe
304L Stainless Steel Pipe
304H Stainless Steel Pipe
304/304L Stainless Steel Tubing
309S Stainless Steel Pipe
310S Stainless Steel Pipe
316L Stainless Steel Tubing
316Ti Stainless Steel Tube
317L Stainless Steel Pipe
321 321H Stainless Steel
347 347H Stainless Steel
904L N08094 Seamless Tubes
17-4 PH 630 UNS S17400 Stainless Steel
253MA S30815 Stainless Steel Tube
S31254 254 SMO Pipe
S31803 Stainless Steel
2205 Duplex Pipe Tubing
S32101 Stainless Steel
S32304 Stainless Steel
2507 Super Duplex Pipe
S32750 Super Duplex Pipe
S32760 Super Duplex Steel
1.4462 Stainless Steel Pipe
ASTM A213 | ASTM A269
ASTM A312 | ASTM A511
ASTM A789 | ASTM A790
ASTM B161 / ASME SB 161 | ASTM B111
EN 10216-5
ASTM A789 ASME SA 789 S31803 S32205 S32101 S32750 S32760 S32304 S31500 S31260 Seamless Tubes
EN 10216-5 1.4462 1.4362 1.4162 1.4410 1.4501 Seamless Tubes
Nickel Alloy Tubing:

UNS N08020 Nickel Alloy 20 Tubing
UNS N02200 Nickel Alloy 200 Tube
UNS N02201 Nickel Alloy 201 Pipe
UNS N04400 400 Nickel Alloy Tubing
N06600 600 2.4816 Nickel Alloy Pipe
N06601 601 2.4851 Nickel Alloy Tubing
N06625 625 2.4856 Nickel Alloy Tubes
N08800 800 Nickel Alloy Tubes
N08810 800H UNS N08810 Nickel Alloy Tubes
N08811 800HT Nickel Alloy Tubes
UNS N08825 825 2.4858 Nickel Alloy Seamless Pipes
ASTM B622 N10276 Nickel Alloy Seamless Tubing
ASTM B622 N06022 Hastelloy C-22 Nickel Alloy Tubes
C28000 Brass Seamless Tubes C44300 Brass Seamless Tubes
C68700 Brass Seamless Tubes
C70600 Copper Nickel Tubes
C71500 Copper Nickel Tubes
DIN 2391 Seamless Precision Steel Tubes
EN 10305-1 E215 E235 E355 Seamless Precision Steel Tube Tubing Tubes
DIN 2393 St28 St34.2 St37.2 St44.2 St52.3 Welded Precision Steel Tubes
EN 10305-2 E195 E235 E355 Welded Cold Drawn Precision Steel Tube