ASTM A513 ERW Carbon and Alloy Steel Mechanical Tubing
ASTM A513 Standard for Electric-Resistance-Welded (ERW) Carbon and Alloy Steel Mechanical Tubing covers round, square, rectangular, and special shape electric-resistance-welded carbon and alloy steel mechanical tubing produced by hot- or cold-rolling. The types of tubing covered here are: Type 1a, as-welded from hot-rolled steel (with mill scale); Type 1b, as-welded from hot-rolled pickled and oiled steel (mill scale removed); Type 2, as-welded from cold-rolled steel; Type 3, sink-drawn hot-rolled steel; Type 4, sink-drawn cold-rolled steel; Type 5, drawn over a mandrel; and Type 6, special smooth inside diameter.
Heat and product analyses shall be made to determine the percentages of chemical elements, to which the steel specimens shall conform to. Tubing shall be free of injurious defects and shall have a workmanlike finish. When specified, tubing shall be coated with a film of rust retarding oil before shipping.
This specification covers electric-resistance-welded carbon and alloy steel tubing for use as mechanical tubing. This specification covers mechanical tubing made from hot- or cold-rolled steel. This specification covers round, square, rectangular, and special shape tubing. Optional supplementary requirements are provided and when desired, shall be so stated in the order.
The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text the SI units are shown in brackets or parenthesis. The values stated in each system may not be exact equivalents; therefore each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. The inch-pound unts shall apply unless the “M” designation of this specification is specified in the order. In this specification hard or rationalized conversions apply to diameters, lengths and tensile strength properties. Soft conversion applies to other SI measurements.
Type |
Size Range
(Round Tubing) |
Electric-Resistance-Welded Tubing from Hot-Rolled Steel
|
outside diameter from 1/2to 15 in.
[10 to 380 mm] |
|
wall from 0.065 to 0.650 in.
[1.65 to 16.50 mm] |
Electric-Resistance-Welded Tubing from Cold-Rolled Steel
|
outside diameter from3/8to 12 in.
[9.5 to 305 mm] |
|
wall from 0.022 to 0.134 in.
[0.56 to 3.40 mm] |
Tube Cutting
Tube Chamfering
Tube Deburring
Tube Coiling
Tube Grooving
Tube Beveling
Tube Threading
Tube Spool Pieces
Tube Bending
Keywords
alloy steel tube; carbon steel tube; mechanical tubing; resistance welded steel tube; steel tube; welded steel tube;
ICS Code
ICS Number Code 23.040.10 (Iron and steel pipes)
Related References:
1. Welding Process and Letter Designations
2. Welding Stainless Steel to other Steel
3. Welding and Post Fabrication Cleaning for Construction and Architectural Application
4. Welded Stainless Steel Pipe
5. Post weld cleaning and finishing of stainless steel
6. Avoid PWHT Post Weld Heat Treatment
7. Fume Associated With Welding Stainless Steel
8. Avoiding Distortion During Welding Stainless Steel
9. Design Strength of Welded Connections
10. Processes for Welding Stainless Steel
11. Brazing Stainless Steel
12. Soldering Stainless Steel
13. Welding Stainless Steel
14. Selection of Welding Consumables Filler
15. Selection of Welding Consumable for Welding Stainless Steel
16. Filler Metals For Welding Stainless Steel
17. Schaeffler and Delong Diagrams for Predicting Ferrite Levels
18. ASTM A501 Hot-Formed Welded and Seamless Steel Structural Tubing
19. ASTM A512 Cold-Drawn Buttweld Carbon Mechanical Tubing
20. ASTM A513 Standard for Electric-Resistance-Welded Carbon and Alloy Steel Mechanical Tubing
21. EN 10217-5/A1 Welded steel tubes for pressure purposes
|