JIS G3452 Carbon Steel Pipe for Ordinary Piping
JIS G3452 Carbon Steel Pipes for Ordinary Piping specifies the carbon steel pipe, hereinafter referred to as the "pipes", used for the pipings for conveying steam, water, oil, gas, air, etc. at comparatively low working pressure.
Remark: The units and numerical values given in { } in this Standard are based on the International System of Units (SI) and are appended for informative reference.
Further, the traditional units accompanied by numerical values in this Standard shall be converted to the SI units and numerical values on Jan. 1, 1991.
Grade and Designation
The pipe shall be classified into one grade and its letter symbol shall be as given in Table 1, and subdivided into black pipes and galvanized ones according to nonexistence of existence of zinc-coated layers.
Chemical composition
The pipe shall be subjected to the test of 10.1 and the resulting ladle analysis values shall be an giben in Table 2.
Table 2. Chemical Compostition
Letter
|
Unot (%)
|
P |
S |
SGP |
0.040 max. |
0.040 max. |
Mechanical properties
Uniformity of Zinc Coating
The galvanized pipe shall be tested by 10.5 and the number of dips in the uniformity test shall be as given in Table 4. In this case, the pipe shall not show a fixed deposit of zinc even after the successive dipping operations of frequency given in Table 4.
Table 4. Uniformity Test
Letter symbol of grade |
Number of dips (One minimum per dip) |
SGP |
5 |
Table 1. Letter Symbol of Grade
Letter sumbol of grade |
Division |
Remark |
SGP |
Black pipe |
Pipe without zinc coating |
Galvanized pipe |
Pipe with zinc coating |
Remark: Where it is necessary to identify the galvanized pipe by the letter symbol on the drawing and other documents, "-ZN" shall be suffixed to the letter sumbol of the grade. This notation, however, shall not be applied to the product itself.
World standard comparative table
KS |
ASTM |
JIS |
API |
DIN |
BS |
Grade Number |
GRADE |
Grade Number |
GRADE |
Grade Number |
GRADE |
Grade Number |
GRADE |
Grade Number |
GRADE |
Grade Number |
GRADE |
D3507 |
SPP |
ASTM A53 |
Type F |
G3452 |
SGP |
5L |
A25-1
A25-2
CI グ
CI ケ |
2440
2441 |
St33-2
St33-2 |
1387
3601 |
BW320 |
7. Hydrostatic Test or Nondestructive Test
7.1 The black pipe shall be tested by 10.6 and the resulting hydrostatic characteristic or nondestructive characteristic shall conform either of the following two. The proference for which of them shall be left to thespecification by the purchaser or to the discretion of the manufacturer.
7.2 Hydrostatic characteristic (Applicable till the end of 1990) When a hydrostatic pressure of 25 kgf/Р {25 bar} (1) is applied, the black pipe shall withstand it witout leakage.
Note (1) 1 bar = 105Pa
8. Hydrostatic Characteristic
8.1 (Applicable on and after Jan. 1, 1991) When a hydrostatic proessure of 2.5 MPa is applied, the black pipe shall
8.2 Nondestructive Characteristic Anondestructive examination by either an ultrasonic test shall be made on the black pipe, and there shall be no signal greater than those produced by the artificial defects of the reference test block of division UE of the working sensitivity specified in JIS G 0582 or division EZ of the working sensitivity specified in JIS G 0583.
9. Dimensions, Weight and Dimensional Tolerances
9.1 The dimensions, weight and dimensional tolerancws of the pipes shall asfollows:
9.2 The length of each pipe shall, as a rule, be 5500 mm or over, the purchaser, however, may specify a length 3600 mm or over, as necessary.
10. Test
11. Inspection
12. Reinspection the pipe may be determined for final acceptance by a retest specified in 4.4 JIS G0303.
13. Marking
Each pipe having passed the inspection shall be marked with the following items. However, the smaller pipes and other pipes specified by the purchaser may be bundled together and marked for each bundle by a suitable means. Im bptj cases. the order of arranging the marked items is not specified.
When approved by the purchaser, part of the items may be omitted.
(1) Letter symbol of grade
(2) Letter symbol denothing the manufacturing processes (5)
(3) Dimensions (6)
(4) Manufacturer's name or its identifying brand
Notes (5)
The letter symbol indicating the manufacturing processes shall be as follows, provided that the dash may be onitted leaving ablank.
Electric-resistance welded steel pipe otherthan hot-finished or cold-finished ones - E - G
Hot-finished electric-resistance welded steel pipe - E - H
Cold-finished electric-resistance welded steel pipe - E - C
Butt -welded steel pipe - B
(6)
The dimensions shall be expressed by the nominal size.
14. Report
The manufacturer shall submit the test report when previously required by the purchaser.
JIS Number and Corrensponding Foreign Standards
|
|
|
|
NF |
ISO |
Standard Number |
Grade |
Tupe |
STDN |
Grade |
T |
STDN |
Grade |
T |
STDN |
Grade |
T |
STDN |
Grade |
T |
STDN |
Grade |
T |
G3452 |
SGP |
C |
A53 |
Type F |
C |
|
|
|
1615
|
St 33-2
|
C
|
A49-145
|
TS34-1
|
C
|
65
|
TW
|
C
|
|
|
|
|
|
|
|
|
|
2441 |
St33-2 |
C |
A49-146 |
TS334-a |
C |
559 |
TWO |
C |
Related References:
JIS Pipe Tube Fitting Standard
JIS-Japan Industrial Standards
|