EN 10217-7 1.4162 1.4462 1.4362 1.4410 1.4501 Tubes soudés en acier inoxydable
EN 10217-7 1.4162 1.4462 1.4362 1.4410 1.4501 Tubes soudés en acier inoxydable
EN 10217-7 1.4301 1.4307 1.4948 1.4541 1.4878 1.4550 1.4401 1.4405 1.4571 1.4438 1.4439 1.4833 1.4845 Tubes soudés en acier pour usages sous pression
We are EN 10217-7 1.4162 1.4462 1.4362 1.4410 1.4501 Welded Stainless Steel Pipes Manufacturer. is the material standard for stainless steel for tubes soudés pour pression purposes. This new standard was first published in February 2005.
Included in the standard are composition chimique, delivery conditions and process route symbols, ambient température mechanical properties, some additional optional tests (leak testing, flattening, drift expansion, bend and non-destructive testing) and some dimensional and tolérance requirements. ustenitic, and austenitic-ferritic acier inoxydable duplex grades are included in the range of grades specified in this standard. Only the chemical composition of the stainless steel tubing in the standard are listed in this article.
It is interesting to compare the grades listed in this standard with those in the standard for welded stainless steel tube for general engineering purposes EN 10296-2. See table below. The implication of this is that some grades can be used for pression purposes which cannot be used for general purposes. It is unlikely that this anomaly was the intention of the standards writers.
The chrome and nickel contents are quoted to 2 decimal places in EN 10217-7 whereas EN 10296-2 quotes only 1 dp. The reason for this is not clear.
For grade 1.4307, the composition differs from that inEN 10296-2, in that the Ni content is 8.00/10.00 compared to 8.0/10.5. This reflects the difference in the flat products standards to which the original strip would be made:
EN 10088-2 – Flat products for general purposes 1.4307 Ni 8.0/10.5
EN 10028-7 Flat products for pressure purposes 1.4307 Ni 8.00/10.00
The reason for these differences is not explained in the standard.
It might be expected that any steels appearing in EN 10028-7 Flat products for pressure purposes would appear in the comparable welded tube standard. This is not the case. The following grades in EN 10028-7 are not found in EN 10217-7:
Ferritique grades – 1.4003, 1.4516, 1.4510, 1.4521, 1.4520, 1.4509
Martensitique grades – 1.4313, 1.4418,1.4541
Austénitique grades – 1.4318, 1.4315, 1.4406, 1.4335, 1.4466, 1.4580, 1.4434, 1.4537
Duplex grades – 1.4507,1.4462 1.4162 1.4462 1.4362 1.4410 1.4501
Creep resisting steels – 1.4948, 1.4950, 1.4951, 1.4941, 1.4958, 1.4959, 1.4910, 1.4961
As an alternative to scanning down the list try the ‘find’ facility on your keyboard, using the ‘Ctrl’ and ‘F’ keys together. Type in the term you are looking for in the dialog box that then appears.
| APPLICATION | FR | S.S. | ASTM-ASME | DIN | NFA | GOST |
| Industrie chimique | EN 10217-7 | 219711 219713 | A358-SA358 A312-SA312 A269 ASTM A928 | 17457 | 49147 | gost 11068-81 |
| Produits alimentaires | EN 10217-7 | ASTM A270 | 11850 | 49249 | ||
| Tubes d'échangeur de chaleur | EN 10217-7 | 219711 219713 | A 249–SA 249 | 17457 2818 | 49247 49244 | GOST 11068-81 |
| Tuyauterie | EN 10217-7 | A778 A269 | 17455 | 49147 | ||
| Eau potable | EN 10312 | DVGW541 | ||||
| Éléments décoratifs | EN 10296-2 | ASTM A554 | 17455 2395 | 49647 |
EN 10217-7 Composition chimique Tables
| Désignation | Chemical composition (% by mass – max unless stated) | ||||||||||||
| Steel name | Steel No. | C | Si | Mn | P | S | Cr | Mo | Ni | Cu | N | Autres | |
| Austenitic steel | |||||||||||||
| X2CrNi18-9 | 1.4307 | 0.03 | 1.00 | 2.0 | 0.045 | 0.015 | 17.50 /19.5 | – | 8.0 /10.0 | – | 0.11 | – | |
| X2CrNi19-11 | 1.4306 | 0.03 | 1.00 | 2.0 | 0.045 | 0.015 | 18.00 /20.0 | – | 10.0 /12.0 | – | 0.11 | – | |
| X2CrNiN18-10 | 1.4311 | 0.03 | 1.00 | 2.0 | 0.045 | 0.015 | 17.00 /19.5 | – | 8.50 /11.5 | – | 0.12 /0.22 | – | |
| X5CrNi18-10 | 1.4301 | 0.07 | 1.00 | 2.0 | 0.045 | 0.015 | 17.00 /19.5 | – | 8.00 /10.5 | – | 0.11 | – | |
| X6CrNiTi18-10 | 1.4541 | 0.08 | 1.00 | 2.0 | 0.045 | 0.015 | 17.00 /19.0 | – | 9.00 /12.0 | – | – | Ti 5xC /0.70 | |
| X6CrNiNb18-10 | 1.4550 | 0.08 | 1.00 | 2.0 | 0.045 | 0.015 | 17.00 /19.0 | – | 9.00 /12.0 | – | – | Nb 10xC /1.00 | |
| X2CrNiMo17-12-2 | 1.4404 | 0.03 | 1.00 | 2.0 | 0.045 | 0.015 | 16.50 /18.5 | 2.0 /2.5 | 10.00 /13.0 | – | 0.11 | – | |
| X5CrNiMo17-12-2 | 1.4401 | 0.07 | 1.00 | 2.0 | 0.045 | 0.015 | 16.50 /18.5 | 2.0 /2.5 | 10.00 /13.0 | – | 0.11 | – | |
| XCrNiMoTi17-12-2 | 1.4571 | 0.08 | 1.00 | 2.0 | 0.045 | 0.015 | 16.50 /18.5 | 2.0 /2.5 | 10.50 /13.5 | – | – | Ti 5xC /0.70 | |
| X2CrNiMo17-12-3 | 1.4432 | 0.03 | 1.00 | 2.0 | 0.045 | 0.015 | 16.50 /18.5 | 2.5 /3.0 | 10.50 /13.0 | – | 0.11 | – | |
| X2CrNiMoN17-13-3 | 1.4429 | 0.03 | 1.00 | 2.0 | 0.045 | 0.015 | 16.50 /18.5 | 2.5 /3.0 | 11.00 /14.0 | – | 0.12 /0.22 | – | |
| X3CrNiMo17-13-3 | 1.4436 | 0.05 | 1.00 | 2.0 | 0.045 | 0.015 | 16.50 /18.5 | 2.5 /3.0 | 10.50 /13.0 | – | 0.11 | – | |
| X2CrNiMo18-14-3 | 1.4435 | 0.030 | 1.00 | 2.0 | 0.045 | 0.015 | 17.00 /19.0 | 2.5 /3.0 | 12.50 /15.0 | – | 0.11 | – | |
| X2CrNiMoN17-13-5 | 1.4439 | 0.03 | 1.00 | 2.0 | 0.040 | 0.015 | 16.50 /18.5 | 4.0 /5.0 | 12.50 /14.5 | – | 0.12 /0.22 | – | |
| X2CrNiMo18-15-4 | 1.4438 | 0.03 | 1.00 | 2.0 | 0.045 | 0.015 | 17.50 /19.5 | 3.0 /4.0 | 13.00 /16.0 | – | 0.11 | – | |
| X1NiCrMoCu31-27-4 | 1.4563 | 0.02 | 0.70 | 2.0 | 0.030 | 0.010 | 26.00 /28.0 | 3.0 /4.0 | 30.00 /32.0 | 0.70 /1.50 | 0.11 | – | |
| X1CrNiMoCu25-20-5 | 1.4539 | 0.02 | 0.70 | 2.0 | 0.030 | 0.010 | 19.00 /21.0 | 4.0 /5.0 | 24.00 /26.0 | 1.20 /2.00 | 0.15 | – | |
| X1CrNiMoCuN20-18-7 | 1.4547 | 0.02 | 0.70 | 1.0 | 0.030 | 0.010 | 19.50 /20.5 | 6.0 /7.0 | 17.50 /18.5 | 0.50 /1.00 | 0.18 /0.25 | – | |
| X1NiCrMoCuN25-20-7 | 1.4529 | 0.02 | 0.50 | 1.0 | 0.030 | 0.010 | 19.00 /21.0 | 6.0 /7.0 | 24.00 /26.0 | 0.50 /1.50 | 0.15 /0.25 | – | |
| Austénitique ferritique acier | |||||||||||||
| X2CrNiN23-4 | 1.4362 | 0.03 | 1.00 | 2.0 | 0.035 | 0.015 | 22.00 /24.0 | 0.10 /0.60 | 3.50 /5.50 | 0.10 /0.60 | 0.05 /0.20 | – | |
| X2CrNiMoN22-5-3 | 1.4462 | 0.03 | 1.00 | 2.0 | 0.035 | 0.015 | 21.00 /23.0 | 2.50 /3.50 | 4.50 /6.50 | – | 0.10 /0.22 | – | |
| X2CrNiMoN25-7-4 | 1.4410 | 0.03 | 1.00 | 2.0 | 0.035 | 0.015 | 24.00 /26.0 | 3.00 /4.50 | 6.00 /8.00 | – | 0.20 /0.35 | – | |
| X2CrNiMoCuWN25-7-4 | 1.4501 | 0.03 | 1.00 | 1.0 | 0.035 | 0.015 | 24.00 /26.0 | 3.00 /4.00 | 6.00 /8.00 | 0.50 /1.00 | 0.20 /0.30 | W 0.50 /1.00 | |
EN 10217 - 7 Tubes soudés en acier pour usage sous pression. Conditions techniques de livraison. Tubes en acier non allié ayant des propriétés spécifiées à température ambiante
EN 10217-7 Propriétés mécaniques des aciers inoxydables
EN 10217-7 Compositions chimiques des tubes en acier inoxydable
EN 10217-5/A1 Tubes soudés en acier pour usage sous pression
Propriétés mécaniques à température ambiante pour EN 10217-7
Propriétés mécaniques à température ambiante pour BS EN 10253-3 et 10253-4
Propriétés mécaniques à température ambiante pour EN 10216-5
Composition chimique des aciers inoxydables selon EN 10216-5
EN 10216-5 tubes en acier inoxydable