EN 10217-7 1.4162 1.4462 1.4362 1.4410 1.4501 Pipa Baja Tahan Karat yang Dilas
EN 10217-7 1.4162 1.4462 1.4362 1.4410 1.4501 Pipa Baja Tahan Karat yang Dilas
EN 10217-7 1.4301 1.4307 1.4948 1.4541 1.4878 1.4550 1.4401 1.4405 1.4571 1.4438 1.4439 1.4833 1.4845 Tabung Baja yang Dilas untuk Keperluan Tekanan
We are EN 10217-7 1.4162 1.4462 1.4362 1.4410 1.4501 Welded Stainless Steel Pipes Manufacturer. is the material standar for stainless steel for tabung yang dilas untuk tekanan purposes. This new standard was first published in February 2005.
Included in the standard are komposisi kimia, delivery conditions and process route symbols, ambient suhu mechanical properties, some additional optional tests (leak testing, flattening, drift expansion, bend and non-destructive testing) and some dimensional and toleransi requirements. ustenitic, and austenitic-ferritic baja tahan karat dupleks grades are included in the range of grades specified in this standard. Only the chemical composition of the stainless steel tubing in the standard are listed in this article.
It is interesting to compare the grades listed in this standard with those in the standard for welded stainless steel tube for general engineering purposes EN 10296-2. See table below. The implication of this is that some grades can be used for tekanan purposes which cannot be used for general purposes. It is unlikely that this anomaly was the intention of the standards writers.
The chrome and nickel contents are quoted to 2 decimal places in EN 10217-7 whereas EN 10296-2 quotes only 1 dp. The reason for this is not clear.
For grade 1.4307, the composition differs from that inEN 10296-2, in that the Ni content is 8.00/10.00 compared to 8.0/10.5. This reflects the difference in the flat products standards to which the original strip would be made:
EN 10088-2 – Flat products for general purposes 1.4307 Ni 8.0/10.5
EN 10028-7 Flat products for pressure purposes 1.4307 Ni 8.00/10.00
The reason for these differences is not explained in the standard.
It might be expected that any steels appearing in EN 10028-7 Flat products for pressure purposes would appear in the comparable welded tube standard. This is not the case. The following grades in EN 10028-7 are not found in EN 10217-7:
Feritik grades – 1.4003, 1.4516, 1.4510, 1.4521, 1.4520, 1.4509
Martensitik grades – 1.4313, 1.4418,1.4541
Austenitik grades – 1.4318, 1.4315, 1.4406, 1.4335, 1.4466, 1.4580, 1.4434, 1.4537
Dupleks grades – 1.4507,1.4462 1.4162 1.4462 1.4362 1.4410 1.4501
Creep resisting steels – 1.4948, 1.4950, 1.4951, 1.4941, 1.4958, 1.4959, 1.4910, 1.4961
As an alternative to scanning down the list try the ‘find’ facility on your keyboard, using the ‘Ctrl’ and ‘F’ keys together. Type in the term you are looking for in the dialog box that then appears.
| APPLICATION | EN | SS | ASTM-ASME | DIN | NFA | GOST |
| Industri kimia | EN 10217-7 | 219711 219713 | A358-SA358 A312-SA312 A269 ASTM A928 | 17457 | 49147 | gost 11068-81 |
| Produk makanan | EN 10217-7 | ASTM A270 | 11850 | 49249 | ||
| Tabung Penukar Panas | EN 10217-7 | 219711 219713 | A 249–SA 249 | 17457 2818 | 49247 49244 | GOST 11068-81 |
| Saluran pipa | EN 10217-7 | A778 A269 | 17455 | 49147 | ||
| Air minum | EN 10312 | DVGW541 | ||||
| Elemen dekoratif | EN 10296-2 | ASTM A554 | 17455 2395 | 49647 |
EN 10217-7 Komposisi Kimia Tables
| Penunjukan | Chemical composition (% by mass – max unless stated) | ||||||||||||
| Steel name | Steel No. | C | Si | Mn | P | S | Cr | Mo | Ni | Cu | N | Lainnya | |
| Austenitic steel | |||||||||||||
| X2CrNi18-9 | 1.4307 | 0.03 | 1.00 | 2.0 | 0.045 | 0.015 | 17.50 /19.5 | – | 8.0 /10.0 | – | 0.11 | – | |
| X2CrNi19-11 | 1.4306 | 0.03 | 1.00 | 2.0 | 0.045 | 0.015 | 18.00 /20.0 | – | 10.0 /12.0 | – | 0.11 | – | |
| X2CrNiN18-10 | 1.4311 | 0.03 | 1.00 | 2.0 | 0.045 | 0.015 | 17.00 /19.5 | – | 8.50 /11.5 | – | 0.12 /0.22 | – | |
| X5CrNi18-10 | 1.4301 | 0.07 | 1.00 | 2.0 | 0.045 | 0.015 | 17.00 /19.5 | – | 8.00 /10.5 | – | 0.11 | – | |
| X6CrNiTi18-10 | 1.4541 | 0.08 | 1.00 | 2.0 | 0.045 | 0.015 | 17.00 /19.0 | – | 9.00 /12.0 | – | – | Ti 5xC /0.70 | |
| X6CrNiNb18-10 | 1.4550 | 0.08 | 1.00 | 2.0 | 0.045 | 0.015 | 17.00 /19.0 | – | 9.00 /12.0 | – | – | Nb 10xC /1.00 | |
| X2CrNiMo17-12-2 | 1.4404 | 0.03 | 1.00 | 2.0 | 0.045 | 0.015 | 16.50 /18.5 | 2.0 /2.5 | 10.00 /13.0 | – | 0.11 | – | |
| X5CrNiMo17-12-2 | 1.4401 | 0.07 | 1.00 | 2.0 | 0.045 | 0.015 | 16.50 /18.5 | 2.0 /2.5 | 10.00 /13.0 | – | 0.11 | – | |
| XCrNiMoTi17-12-2 | 1.4571 | 0.08 | 1.00 | 2.0 | 0.045 | 0.015 | 16.50 /18.5 | 2.0 /2.5 | 10.50 /13.5 | – | – | Ti 5xC /0.70 | |
| X2CrNiMo17-12-3 | 1.4432 | 0.03 | 1.00 | 2.0 | 0.045 | 0.015 | 16.50 /18.5 | 2.5 /3.0 | 10.50 /13.0 | – | 0.11 | – | |
| X2CrNiMoN17-13-3 | 1.4429 | 0.03 | 1.00 | 2.0 | 0.045 | 0.015 | 16.50 /18.5 | 2.5 /3.0 | 11.00 /14.0 | – | 0.12 /0.22 | – | |
| X3CrNiMo17-13-3 | 1.4436 | 0.05 | 1.00 | 2.0 | 0.045 | 0.015 | 16.50 /18.5 | 2.5 /3.0 | 10.50 /13.0 | – | 0.11 | – | |
| X2CrNiMo18-14-3 | 1.4435 | 0.030 | 1.00 | 2.0 | 0.045 | 0.015 | 17.00 /19.0 | 2.5 /3.0 | 12.50 /15.0 | – | 0.11 | – | |
| X2CrNiMoN17-13-5 | 1.4439 | 0.03 | 1.00 | 2.0 | 0.040 | 0.015 | 16.50 /18.5 | 4.0 /5.0 | 12.50 /14.5 | – | 0.12 /0.22 | – | |
| X2CrNiMo18-15-4 | 1.4438 | 0.03 | 1.00 | 2.0 | 0.045 | 0.015 | 17.50 /19.5 | 3.0 /4.0 | 13.00 /16.0 | – | 0.11 | – | |
| X1NiCrMoCu31-27-4 | 1.4563 | 0.02 | 0.70 | 2.0 | 0.030 | 0.010 | 26.00 /28.0 | 3.0 /4.0 | 30.00 /32.0 | 0.70 /1.50 | 0.11 | – | |
| X1CrNiMoCu25-20-5 | 1.4539 | 0.02 | 0.70 | 2.0 | 0.030 | 0.010 | 19.00 /21.0 | 4.0 /5.0 | 24.00 /26.0 | 1.20 /2.00 | 0.15 | – | |
| X1CrNiMoCuN20-18-7 | 1.4547 | 0.02 | 0.70 | 1.0 | 0.030 | 0.010 | 19.50 /20.5 | 6.0 /7.0 | 17.50 /18.5 | 0.50 /1.00 | 0.18 /0.25 | – | |
| X1NiCrMoCuN25-20-7 | 1.4529 | 0.02 | 0.50 | 1.0 | 0.030 | 0.010 | 19.00 /21.0 | 6.0 /7.0 | 24.00 /26.0 | 0.50 /1.50 | 0.15 /0.25 | – | |
| Austenitik feritik baja | |||||||||||||
| X2CrNiN23-4 | 1.4362 | 0.03 | 1.00 | 2.0 | 0.035 | 0.015 | 22.00 /24.0 | 0.10 /0.60 | 3.50 /5.50 | 0.10 /0.60 | 0.05 /0.20 | – | |
| X2CrNiMoN22-5-3 | 1.4462 | 0.03 | 1.00 | 2.0 | 0.035 | 0.015 | 21.00 /23.0 | 2.50 /3.50 | 4.50 /6.50 | – | 0.10 /0.22 | – | |
| X2CrNiMoN25-7-4 | 1.4410 | 0.03 | 1.00 | 2.0 | 0.035 | 0.015 | 24.00 /26.0 | 3.00 /4.50 | 6.00 /8.00 | – | 0.20 /0.35 | – | |
| X2CrNiMoCuWN25-7-4 | 1.4501 | 0.03 | 1.00 | 1.0 | 0.035 | 0.015 | 24.00 /26.0 | 3.00 /4.00 | 6.00 /8.00 | 0.50 /1.00 | 0.20 /0.30 | W 0.50 /1.00 | |
EN 10217 - 7 Tabung baja yang dilas untuk keperluan tekanan. Kondisi pengiriman teknis. Tabung baja non-paduan dengan sifat suhu ruangan tertentu
EN 10217-7 Sifat Mekanis untuk Baja Tahan Karat
EN 10217-7 Komposisi Kimiawi Pipa Baja Tahan Karat
EN 10217-5/A1 Tabung baja yang dilas untuk keperluan tekanan
Ambient temperature mechanical properties for EN 10217-7
Ambient temperature mechanical properties for BS EN 10253-3 and 10253-4
Sifat mekanis suhu sekitar untuk EN 10216-5
Komposisi kimiawi baja tahan karat untuk EN 10216-5
Pipa tabung baja tahan karat EN 10216-5