EN 10088-3 Mechanical Properties of Ferritic Stainless Stee
EN 10088-3 gives the mechanical properties for stainless steel semi-finished products, bars, rods and sections for general purposes. This article covers ferritic stainless steel supplied as bright bars The properties given are proof strength, tensile strength, elongation and hardness.
EN 10088-3 was originally published in 1995. The second, current version, EN 10088-3:2005, has superseded EN 10088-3:1995, which was withdrawn by BSi on 20th June 2005.
The tables shown here only have the 2005 tensile strength properties ranges of the ferritic steel. Four new 'special' ferritic grades 1.4520, 1.4511, 1.4526 and 1.4509 have been added.
This article covers bright products which were introduced in the 2005 edition.
The ferritic steel are in the annealed condition. The annealing treatment may be omitted, if the conditions for hot working and subsequent cooling are such that the requirements for the mechanical properties of the product and the resistance to intergranular corrosion as defined in EN ISO 3651-2 are obtained.
EN 10088-3 mechanical properties - ferritic stainless steel bright bar including lengths cut from wire
| Designation |
Mechanical properties min unless stated |
| Steel name |
Steel number |
Max Thickness or diameter mm 1) |
Proof strength Rp0.2N/mm2 |
Tensile strength RmN/mm2 |
Elongation A2) % |
| Standard Grades |
| X6Cr17 |
1.4016/430 |
103) |
320 |
500/750 |
8 |
| 10<t<16 |
300 |
480/750 |
8 |
| 16<t<40 |
240 |
400/700 |
15 |
| 40<t<63 |
240 |
400/700 |
15 |
| 63<t<100 |
240 |
400/630 |
20 |
| X6CrMoS17 |
1.4105 |
103) |
330 |
530/780 |
7 |
| 10<t<16 |
310 |
500/780 |
7 |
| 16<t<40 |
250 |
430/730 |
12 |
| 40<t<63 |
250 |
430/730 |
12 |
| 63<t<100 |
250 |
430/630 |
20 |
| X6CrMo17-1 |
1.4113/434 |
103) |
340 |
540/700 |
8 |
| 10<t<16 |
320 |
500/700 |
12 |
| 16<t<40 |
280 |
440/700 |
15 |
| 40<t<63 |
280 |
440/700 |
15 |
| 63<t<100 |
280 |
440/660 |
18 |
| Special Grades |
| X2CrTi17 |
1.4520 |
103) |
320 |
500/750 |
8 |
| 10<t<16 |
300 |
480/750 |
10 |
| 16<t<40 |
240 |
400/700 |
15 |
| 40<t<50 |
240 |
400/700 |
15 |
| X3CrNb17 |
1.4511 |
103) |
320 |
500/750 |
8 |
| 10<t<16 |
300 |
480/750 |
10 |
| 16<t<40 |
240 |
400/700 |
15 |
| 40<t<50 |
240 |
400/700 |
15 |
| X6CrMoNb17-1 |
1.4526 |
103) |
340 |
540/700 |
8 |
| 10<t<16 |
320 |
500/700 |
12 |
| 16<t<40 |
280 |
440/700 |
15 |
| 40<t<50 |
280 |
440/700 |
15 |
| X2CrTiNb18 |
1.4509 |
103) |
320 |
500/750 |
8 |
| 10<t<16 |
300 |
480/750 |
10 |
| 16<t<40 |
240 |
400/700 |
15 |
| 40<t<50 |
240 |
400/700 |
15 |
Note
- Width across flats for hexagons.
- Elongation is valid only for dimensions of 5mm and above. For smaller diameters, the minimum elongation has to agreed upon at the time of the enquiry and order
- In the range 1mm<t<5mm valid only for rounds. The mechanical properties of non round bars with thicknesses <5mm have to be agreed at the time of the enquiry and order
 EN 10088-3 Stainless steels. Technical delivery conditions for semi-finished products, bars, rods, wire, sections and bright products of corrosion resisting steels for general purposes
Related References:
1. EN 10088-3 Mechanical Properties of Martensitic Precipitation
2. EN 10088-3 Mechanical properties austenitic stainless steel bar
3. EN 10088-3 Mechanical Properties of Duplex Stainless Steel Bar
4. EN 10088-3 Duplex Steel Long Products Mechanical Properties
5. EN 10088-3 Mechanical Properties of Ferritic Stainless Steel
6. EN 10088-3 Mechanical properties austenitic stainless steel bar
7. EN 10088-3 Cold Worked Wire Mechanical Properties
8. EN 10088-3 Stainless Steel Long Products Grades
9. EN 10088-3 Mechanical Properties of ferritic steel long product
10. EN 10088-3 Mechanical Properties of Martensitic and Precipitation Hardening Stainless Steel Bright Bars
11. EN 10088-3 Mechanical of Martensitic and Precipitation Hardening Long Products
12. Permissible Analysis Tolerances on Cast Ranges in EN 10088-3
|
